Any use of this product means being aware of and agreeing to the following:
Usage Agreement: Zen Link™ is an expansion product that requires a separate purchase of a Cronus Zen™ device. Access to a Windows 10/11 PC is required for initial updating and completion of Zen Link™ setup. At this time, Cronus Zen™ itself still requires frequent access to a Windows 10/11 PC for Zen Studio™ configuration. Zen Link™ uses PS5® Remote Play which requires an active PSN® account.
Trademark Notice: Zen Link™ is a trademark of Collective Minds Gaming Co. Ltd. All product names, logos, brands, and other trademarks, images, or videos mentioned in this manual or on the website are used solely for identification purposes and remain the property of their respective trademark holders. These trademark holders are NOT affiliated with Collective Minds Gaming Co. Ltd., and they DO NOT sponsor or endorse its products, services, or websites. The trademarks "PlayStation®", PlayStation®5", PS5®, PSN®, DualSense® are owned by Sony Interactive Entertainment.
This changelog is provided for educational purposes only.
Zen Link™ is an expansion module that adds Wi-Fi functionality to Cronus Zen™ (separate purchase). It opens up some exciting future possibilities and it currently provides full PS5® console support through Remote Play without the need to be tethered to a PC. Simply configure on your PC once, and then plug into your Cronus Zen™ device to use it on your PS5® console without issue. Please follow this guide in order and you will be setup in no time!
Windows 10/11 PC is still required for Zen Link™ initial setup, and for Cronus Zen™ configuration in Zen Studio™ at this time!
*** PS5® Remote Play MUST be run on your PC, logged in, and successfully connected to your PS5® console at least once, before attempting to set up the Zen Link™ device ***
To set up Remote Play, visit the following link here for detailed instructions. The Windows PC version of Remote Play MUST be used! Once you have completed setup and connected to your PS5® console, you can close the Remote Play application.
Using the supplied short cable, plug Zen Link™ into your Windows PC.
After you install Zen Studio 1.6.0 build 13 or higher, there should be a Zen Link Configurator shortcut on your desktop. Just Double Click on this shortcut to open the configurator.
Proceed with the following. Please be patient between clicks as the configurator is working:
a. Click "Read Settings From Windows". Ensure it is the 2.4 Ghz Wi-Fi credentials.
b. Click "Load Console Data".
c. Click "Save All To Device".
d. Click "Restart Device".
After Zen Link™ has restarted, its LEDs should turn ORANGE to confirm Wi-Fi is connected.
The Zen Link™ firmware update will start with blinking BLUE LEDs on the device, and the configurator's status bar will display "Flashing" with the current progress. DO NOT remove the device, and wait for "Done. Rebooting Device".
The Zen Link™ LEDs will turn back to ORANGE. It has now rebooted, disconnected from the configurator, and it is ready for use! (If unplugged and plugged back in, a CYAN LED will be briefly shown to confirm Zen Console Mode is ready). Click "Yes" to close the configurator.
As Zen Link™ is now configured with your 2.4 GHz Wi-Fi credentials, it no longer needs your PC to connect. You can now return your PC to its usual way of connecting to the internet.
One time Initial Setup MUST be completed!
Zen Link™ MUST be within reasonable range of your wireless router/modem to ensure smooth operation; otherwise lag and disconnecting could occur. You should have a good idea from your other devices as to whether you are within a decent Wi-Fi signal range.
For the best possible experience, connect your PS5® console via wired ethernet, if possible.
Plug Cronus Zen™ into your PS5® console.
Using the supplied short cable, plug Zen Link™ into the A1 port (left side):
Wait for the LED sequence to settle on GREEN.
Use Cronus Zen™ on your PS5® as normal.
Cronus Zen™ fulfills the role of a soundcard to support headset audio & microphone for the Zen Link™ remote play connection. For this to work, your controller MUST be using a WIRED connection to the Cronus Zen™. 3.5mm audio & microphone WILL NOT be available over a wireless Bluetooth® controller connection!
If you need to use your controller wirelessly, other options exist such as purchasing a USB wired headset or wireless headset that is compatible with PS5®.
Please refer to the various Zen Link™ LED indicators and their meanings below to assist with troubleshooting:
LED indicators in Config PC Mode:
PURPLE LED means Config Mode. Initially shown when entering Config Mode.
Blinking RED LED means no Wi-Fi settings are setup.
ORANGE LED means successfully connected to Wi-Fi.
Blinking BLUE LED means firmware is updating. DO NOT unplug during this!
CYAN LED means Zen Console Mode ready. Briefly shown when unplugged/plugged back in.
LED indicators in Zen Console Mode:
CYAN LED means Zen Console Mode ready.
ORANGE LED means connecting to Wi-Fi.
Blinking RED LED means no Wi-Fi found.
Blinking PURPLE LED means failure to connect to console. Test Remote Play on your PC.
Single LIGHT GREEN flash then LED off means retrying connection.
RED/BLUE flashing means Remote Play disconnected. Check your Wi-Fi signal strength/range. Ensure your controller is connected/paired to your Cronus Zen™.
Steady GREEN means successfully connected and ready to play.
PURPLE and GREEN means no update available.
Requirements: Zen Link™ is a 2.4 GHz device, so before starting setup, you MUST ensure your Windows PC is connected to a 2.4 GHz Wi-Fi capable network. In most cases, a 5 Ghz network that is not separated from the 2.4 GHz band will work, but if you have trouble connecting 2.4 Ghz devices, you may need to separate the bands. If your PC is using a wired ethernet connection, you will need to unplug it for now!
You MUST have already configured PS5® Remote Play on your setup PC to be able to proceed with Zen Link™ setup. This will be a one time setup for the most part, only requiring a refresh if you change your network settings or PSN® profile login.
To enter ZenLinkConfigurator Mode, HOLD the CONFIG BUTTON while plugging into PC until the LEDs turn PURPLE, followed by ORANGE (Wi-Fi connected) or BLINKING RED (no Wi-Fi set).
To perform a Factory Reset, HOLD the FACTORY RESET BUTTON (paperclip hole underneath) while plugging into the PC until the LEDs turn PURPLE then BLINK RED.
